MPU-9250

ICM-20948 is a 9-axis motion-tracking IMU from TDK InvenSense in a QFN-24 package — gyroscope, accelerometer and magnetometer in one chip, marked Production but Not Recommended for New Designs. The integrated 9-axis sensing was the selection point: full orientation tracking from a single device for drones and AR/VR controllers. Selection advice: because TDK flags this part NRND, treat it as a legacy reference — for new designs qualify a current-production 9-axis IMU before committing the BOM; for existing builds, send quantity and date-code requirements with your RFQ and we will check remaining traceable stock. Parameters verified against the TDK official product page. We reconfirm the offered lot before quotation and reply within 24 hours.

ICM-42670-P is a TDK InvenSense 6-axis MotionTracking IMU combining 3-axis gyroscope and 3-axis accelerometer in 2.5x3 mm LGA-14 — for high-performance motion sensing in industrial robotics, AR/VR headsets and gaming controllers. 16-bit resolution, ±2/4/8/16 g accelerometer ranges, I3C/I2C/SPI interfaces, 550 µA operating current, and -40 to +85°C range. Ranked #16 on the 创芯指数 March 2026 hot-search TOP 50 with 22,506 searches and a 222.90% month-on-month increase, as IMU demand extends from consumer into robotics and drones. Selection advice: the -P code is the standard LGA-14 package — at 0.55 mA in low-noise mode it undercuts the ICM-42688-P (0.88 mA) for battery-powered designs; the I3C interface suits new sensor hubs while I2C keeps legacy compatibility. Parameters verified against TDK InvenSense documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ICM-42688-P is a low-noise 6-axis gyroscope and accelerometer from TDK InvenSense in an LGA-14 package — for drones, robotics, wearables and image stabilization. The low-noise 6-axis IMU with on-chip sensor fusion support is the selection point: it delivers stable orientation output for motion tracking without a separate co-processor. Selection advice: confirm your full-scale range and output data rate requirements against the datasheet — the P variant targets high-performance applications versus cost-optimized IMUs. Verify your interface (I2C/SPI) and power budget. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MPU-6050 is a TDK InvenSense 6-axis MEMS motion-tracking device in QFN-24 (4.0 x 4.0 x 0.9 mm) — 3-axis gyroscope (±250/500/1000/2000 °/s) plus 3-axis accelerometer (±2/4/8/16 g) with 16-bit ADCs, an on-chip Digital Motion Processor (DMP) engine, 1024-byte FIFO, digital temperature sensor, 10,000 g shock tolerance and an auxiliary master I2C bus for external magnetometers, VDD 2.375–3.46 V with a separate VLOGIC pin setting the I2C interface levels (1.71 V to VDD). The DMP plus FIFO is the selection point: motion-fusion, gesture and timing work runs on-chip while the host sleeps, which is why this part defined the Arduino/drone gimbal era of low-cost IMUs. Selection advice: the MPU-6050 supports I2C only — if you need SPI, the MPU-6000 is the pin-compatible twin with SPI plus a single supply pin; do not treat them as code-identical. TDK lists MPU-6050 as Obsolete — production has stopped and final shipment is complete, so treat any offer as end-of-life stock: require date-code traceability and, for new designs, evaluate the current TDK IMU family instead. Evidence: InvenSense MPU-6000/MPU-6050 product specification (Rev. 3.4) and TDK product pages confirm the ranges, VDD, VLOGIC, QFN-24 and obsolete status. Match the full MPU-6050 code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ACS37002LMABTR-050B5 is an isolated Hall-effect current sensor from Allegro MicroSystems in a 16-pin SOIC package, with a 50 A measurement range on tape and reel — for high-current motor drives, solar inverters and industrial power. The 50 A range in a standard SOIC-16 is the selection point: high-current isolated sensing without a bulky module or external shunt. Selection advice: the 050B5 code denotes the 50 A bidirectional variant — the ACS37002 ships in multiple ranges that are not interchangeable, so match the full ACS37002LMABTR-050B5 code. Confirm your current range, bandwidth and isolation requirements against the datasheet. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ACS712ELCTR-05B-T is an isolated Hall-effect current sensor from Allegro MicroSystems in an 8-pin SOIC package, with a 5 A measurement range — for motor control, power supplies and overcurrent protection. The integrated Hall sensor with 2.1 kV isolation is the selection point: current sensing with galvanic isolation and no shunt resistor, so no power dissipation or high-side measurement headaches. Selection advice: the 05B code denotes the ±5 A range — the ACS712 ships in 5/20/30 A variants with different sensitivities that are not interchangeable, so match the full ACS712ELCTR-05B-T code. Confirm your current range and bandwidth needs against the datasheet. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ACS712ELCTR-20A-T is an Allegro MicroSystems fully integrated Hall-effect linear current sensor in 8-pin SOIC (0.154 in narrow), tape-and-reel packing (TR) — ±20 A sensing range, 100 mV/A output sensitivity, ratiometric voltage output centered at 2.5 V, 5 µs output rise time, 80 kHz typical bandwidth, 4.5–5.5 V single supply, ±1.5% total output error at 25 °C, 1.2 mΩ primary conductor resistance, 2.1 kV RMS isolation between pins 1–4 and 5–8, −40 to +85 °C. The integrated copper conduction path is the selection point: current flows through the package itself, so sensing adds only 1.2 mΩ of series resistance — no external high-power shunt resistor and no isolation optocoupler needed for 2.1 kV RMS separation in motor control, SMPS, load monitoring and overcurrent protection. Selection advice: this is the bidirectional 20 A member — the ±5 A and ±30 A siblings differ in sensitivity and bandwidth, and the 20 A choice trades resolution against range, so match the range to your actual fault-current envelope. Allegro notes the ACS712 is not intended for automotive applications. Evidence: Allegro ACS712 datasheet and distributor listings confirm ±20 A, 100 mV/A, 80 kHz, 2.1 kV RMS, 8-SOIC and tape-and-reel packing. Match the full ACS712ELCTR-20A-T code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ACS712ELCTR-30A-T is an Allegro Hall-effect linear current sensor in 8-SOIC — ±30 A bidirectional sensing, 66 mV/A sensitivity, 5 µs output response time, 80 kHz bandwidth, ±1.5% accuracy, 2.1 kVRMS galvanic isolation between the current path and the output, 1.2 mΩ internal conductor, 5 V single supply, ratiometric analog voltage output, tape-and-reel packing (T), -40 to +85 °C. The zero-insertion-loss sensing is the selection point: no external shunt resistor and no power dissipated in the sense path — the current flows through a 1.2 mΩ copper path while the output voltage is proportional to AC or DC current. Selection advice: this is the ±30 A version — the ACS712 also comes in 5 A and 20 A versions with different sensitivity, so match the full ACS712ELCTR-30A-T code to your current range. The FILTER pin lets you set bandwidth with an external capacitor. Evidence: Allegro ACS712 datasheet and distributor listings confirm ±30 A, 66 mV/A, 5 µs, 8-SOIC and reel packing. Match the full ACS712ELCTR-30A-T code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADP5200 is a Panasonic PS-A series compound pressure sensor in 6-pin SMD module — ±100 kPa rated pressure (±200 kPa proof), amplified 0 V to 4.5 V analog output, ±1.25 %FS accuracy, temperature compensated, 5 V drive, -10 °C to +60 °C. The amplified temperature-compensated output is the selection point: it drops straight into a microcontroller ADC with no external instrumentation amplifier or calibration network. Selection advice: ADP5200 is the ±100 kPa SMD code — the ADP5100 is the DIP twin and the ADP5240 covers 100 kPa gauge; match the pressure type (compound vs gauge) to your medium. Honest lifecycle note: this series is in Last Time Buy — available for existing designs, so confirm the lot and consider a lifetime buy for ongoing production. Evidence: the Panasonic PS-A official catalog confirms the pressure range and package codes. State quantity and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADXL345BCCZ is a digital three-axis accelerometer from Analog Devices in a 14-pin LGA package — for motion detection, tilt sensing, tap/double-tap input and free-fall detection in handheld, wearable and industrial devices. Its advantage is the built-in activity/inactivity and tap sensing: motion events wake the host from sleep without continuous polling, which cuts system power in battery designs. Selection advice: the CCZ suffix denotes the LGA-14 package on tape and reel — the ADXL345 ships in several packages, so match the full code to your layout. For new designs, compare against current-generation accelerometers on power and noise if your budget allows; for existing designs, match the code exactly. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.