TCAN1044ADRQ1

TJA1057GT/0Z is an NXP AEC-Q100 qualified high-speed CAN FD transceiver in SOIC-8 — for cost-optimized automotive CAN networks: the workhorse PHY for body and chassis CAN buses. CAN FD data rates, optimized EMC performance for 12V automotive systems, standby mode for low-power wake-up, and pin-compatible across the TJA1057 family. Heat evidence: high-speed CAN remains the dominant automotive bus by volume — every vehicle ships with multiple CAN transceivers, and the GT variant adds CAN FD for next-generation platforms. Selection advice: the GT is the CAN FD-capable variant — for classic CAN only the TJA1057T costs less; the /0Z code is the SOIC-8 standard package. AEC-Q100 qualified. Parameters verified against NXP documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TJA1057GT/1Z is an NXP high-speed CAN FD transceiver in SOIC-8 — for automotive and industrial CAN networks: 5 Mbps CAN FD, 4.75–5.25 V supply, -40°C to +150°C, 8 kV ESD, TXD dominant timeout, silent mode. Lifecycle note: Mouser flags this variant NRND (not recommended for new designs) — suitable for repairs, legacy production and existing designs; for new CAN FD designs qualify a current-production transceiver. Selection advice: the /1Z is the SOIC-8 reel variant — the TJA1057 family also ships in HVSON; match the package to your layout. Parameters verified against NXP documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TJA1462BT/0Z is an NXP CAN FD signal-improvement (SIC) transceiver in SOIC-8 — for automotive CAN FD networks where ringing limits data rate or topology size: body controllers, gateways and battery management. Active signal improvement per ISO 11898-2:2024 enables reliable CAN FD up to 8 Mbps in larger, more complex networks than conventional transceivers tolerate, with AEC-Q100 Grade 1 qualification. Selection advice: this is a pin-compatible drop-in for the classic TJA1051 on this site — upgrade the footprint without PCB changes when moving to CAN FD; for non-SIC CAN FD at lower cost the TCAN1044 family is the alternative. The BT/0Z code is the SOIC-8 standard package — confirm the exact suffix against your assembly process. Parameters verified against NXP documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MCP2562FDT-E/MF is a Microchip high-speed CAN FD transceiver in 8-lead DFN (3×3 mm), tape and reel — up to 8 Mbps CAN FD data rates, 4.5–5.5 V supply, 5 µA standby, VIO pin for direct interfacing to 1.8–5.5 V controllers, SPLIT pin for stabilized common mode, TXD dominant timeout, permanent-dominant detection, thermal shutdown and short-circuit protection, −40 °C to +125 °C. The CAN FD rate is the selection point: classic CAN tops out at 1 Mbps, while this part handles the flexible-data-rate frames modern automotive and industrial buses require — without it, an 8 Mbps bus silently fails. Selection advice: the FD in the part number is the CAN FD capability — the non-FD MCP2561/2562 (1 Mbps) is cheaper but not interchangeable on an FD bus; T means tape and reel, E is the extended −40 to +125 °C grade, MF is the DFN-8 package (SN is SOIC-8). An unpowered node does not load the bus. Evidence: the Microchip MCP2561/2FD datasheet (packaging and marking tables) and Farnell/Newark listings confirm 8 Mbps, DFN-8, −40 to +125 °C and reel packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TJA1043T/1J is an NXP high-speed CAN FD transceiver in SOIC-14 — for automotive CAN networks needing 5 Mbps flexible data-rate. Third-generation CAN transceiver, ISO 11898-2:2016, standby and sleep modes with local/remote wake-up, VIO for 3 V/5 V MCU interfacing, ±8 kV bus ESD, AEC-Q100 qualified. Heat evidence: Future Electronics shows 77,500 in stock with 255,000 on order — CAN FD adoption accelerates as the TJA1050 moves to EOL and designs migrate to this upgrade path. Selection advice: the /1J code is the SOIC-14 reel variant — a functional superset of the TJA1042 with improved EMC; listen-only mode aids node diagnostics. Parameters verified against NXP and distributor documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ISO1044BD is a Texas Instruments galvanically isolated CAN FD transceiver in SOIC-8 — for CAN buses that cross ground domains: EV battery packs, solar inverters and motor drives where noise currents must not enter the local ground. 5 Mbps CAN FD data rate, ±58V DC bus fault protection, 3000 VRMS isolation barrier, and -40 to +125°C operation. Selection advice: this is the CAN FD generation — for classic CAN isolation the ISO1050 on this site is the established choice; the SOIC-8 D package replaces optocoupler-plus-transceiver discrete solutions in a fraction of the board area. Pair with an isolated power supply for a complete isolated CAN node. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

SN65HVD230DR is a Texas Instruments 3.3 V CAN transceiver in SOIC-8, tape and reel — for industrial automation, motor control and building systems adding CAN bus to 3.3 V MCUs. ISO 11898-compliant 1 Mbps transceiver running from a single 3.3 V supply is the selection point: no 5 V rail needed for the CAN physical layer. Selection advice: the R suffix denotes tape and reel. Low-power standby (370 µA typical) suits battery-backed nodes; ±16 kV HBM bus ESD, thermal shutdown and open-circuit fail-safe harden the bus; up to 120 nodes per bus. It is documented as a low-power 3.3 V replacement for the classic 5 V PCA82C250 footprint — for new native 5 V CAN designs, stay with a 5 V transceiver. Not automotive qualified — for AEC-Q100, ask about the Q1-qualified variant. TI lists this part as Active. Parameters verified against distributor and manufacturer documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

SN65HVD3082EDR is a Texas Instruments SN65HVD3082E low-power half-duplex RS-485 transceiver — up to 200 kbps signaling rate, single 5 V supply, 8-pin SOIC, tape-and-reel packing of 2500 (R suffix; EP is the PDIP tube version), -40 to +85 °C. The low power and robustness are the selection point: 0.3 mA typical supply current, 1/8-unit-load input supporting up to 256 nodes on the bus, 15 kV bus-pin ESD protection and fail-safe receiver for open/idle lines. Selection advice: the 3082E is the 200 kbps variant — for 1 Mbps choose SN65HVD3085E or for 20 Mbps SN65HVD3088E, which are pin-compatible upgrades in the same family. This is half-duplex (one driver, one receiver); full-duplex RS-422/485 needs a different device. TI lists this code as Active. Evidence: TI SNx5HVD308xE datasheet (ordering information and package addendum) confirms 200 kbps, SOIC-8, 2500/reel packing and -40 to +85 °C. Match the full SN65HVD3082EDR code for data rate, package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DP83848IVVX/NOPB is a Texas Instruments DP83848I industrial-temperature 10/100 Mbps Ethernet PHY transceiver — 48-pin LQFP (7 × 7 mm), MII/RMII/SNI MAC interfaces, auto-MDIX, energy-detect mode, JTAG, 3.3 V, tape-and-reel packing of 1000, -40 to +85 °C. The industrial temperature range is the selection point: the I grade covers factory automation and outdoor equipment where commercial-grade PHYs fail, with auto-MDIX eliminating crossover-cable concerns. Selection advice: this is a PHY only — it needs an external MAC (MCU or switch) and a magnetics module. The V suffix is the 48-LQFP package; NOPB is the lead-free RoHS variant. For Gigabit Ethernet choose a different PHY family, since this is strictly 10/100. TI lists this code as Active. Evidence: TI DP83848I datasheet and distributor listings confirm 10/100 Mbps PHY, 48-LQFP, MII/RMII, -40 to +85 °C and 1000/reel packing. Match the full DP83848IVVX/NOPB code for temperature grade and package. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DP83867ERGZR is a Texas Instruments 10/100/1000BASE-T Gigabit Ethernet PHY in 48-pin VQFN (7x7mm) — for industrial Ethernet nodes where deterministic latency and diagnostics matter: PLCs, machine vision cameras and grid automation. RGMII and SGMII MAC interfaces, IEEE 1588 start-of-frame detection for time-sensitive networking, cable diagnostics, and 8kV IEC 61000-4-2 ESD protection. Selection advice: the E variant covers -40 to +105°C — for commercial 0 to +70°C the CS code costs less, and the IR code targets -40 to +85°C industrial; for 10/100 Mbps only the DP83848 on this site is the economical choice. 457mW full-power draw suits fanless enclosures. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Skyworks and Qorvo expect to close their $22 billion merger on or about October 5, 2026. What the deal changes for RF front-end buyers — and a five-point checklist for before and after close.