ICM-20948 alternatives & equivalent parts
TDK InvenSense 9-axis MotionTracking device: 3-axis gyroscope (+/-250 to +/-2000 dps), 3-axis accelerometer (+/-2 to +/-16 g) and 3-axis compass (+/-4900 uT, AK09916) with an on-chip DMP, over SPI/I2C. Lifecycle first: TDK marks the ICM-20948 itself EOL and publishes a migration guide to its ICM-456xx family, so this page is about sustaining existing designs, not starting new ones. — common packages: QFN-24, 3 x 3 x 1 mm. Each candidate below cites its manufacturer datasheet; check the relationship badge before substituting.
3 verified alternatives for ICM-20948
| Alternative | Manufacturer | Relationship | Key differences | Source |
|---|---|---|---|---|
| MPU-9250 | TDK InvenSense | Pin-compatibleDrop-in: same footprint and pinout. | Same 3 x 3 x 1 mm 24-pin QFN footprint: TDK's own material describes the ICM-20948 as pin-to-pin compatible with the MPU-9250, but the register map and DMP firmware are not code-compatible, so a driver rewrite is required. Electrically it is narrower: VDD is 2.4-3.6 V (versus 1.71-3.6 V), so it cannot run in a 1.8 V-VDD ICM-20948 design, and its AK8963 compass range is +/-4800 uT versus +/-4900 uT. Lifecycle: the MPU-9250 is itself obsolete (TDK no longer publishes a product page for it), so it only suits sustaining existing stock, never a new design. | Distributor listing (TDK has removed the MPU-9250 product page; lifecycle shown as Obsolete) |
| LSM9DS1 | STMicroelectronics | Functional alternativeSame function: board or design change needed. | Also 9-axis with 16-bit output and I2C/SPI, but the package is an LGA-24 measuring 3.5 x 3 x 1.0 mm (larger than the source's 3 x 3 mm) with a completely different pinout, so it needs a PCB redesign and a new driver (different register map, separate magnetometer I2C address). Parameter gaps: analog supply 1.9-3.6 V (cannot use a 1.71-1.9 V rail), gyro full scales +/-245/500/2000 dps (no +/-1000 dps step), magnetometer tops out at +/-16 gauss (+/-1600 uT) versus +/-4900 uT, and there is no DMP/fusion processor. ST's own product page steers new designs to the LSM6DSO instead. | ST product page |
| BMI270 | Bosch Sensortec | Functional alternativeSame function: board or design change needed. | Only a 6-axis IMU (16-bit accelerometer +/-2/4/8/16 g plus gyroscope +/-125-2000 dps) in a 14-pin LGA of 2.5 x 3.0 x 0.8 mm, a wholly different footprint and pinout from the 24-pin source. It has no magnetometer, so compass/heading output is lost unless an external magnetometer is added through its auxiliary I2C master interface (for example a BMM150) and fused on the host. Supply is VDD 1.71-3.6 V with a wider VDDIO range of 1.2-3.6 V and SPI up to 10 MHz, but none of that makes it a drop-in for a 9-axis design. Of the three candidates it is the only one that is a current, active product. | Bosch Sensortec product page |
Pre-replacement checklist
- Start with lifecycle: the source part is EOL and the MPU-9250 is obsolete; for a new design follow TDK's ICM-456xx migration path instead of any part on this page
- Check whether you actually need the magnetometer: the BMI270 is 6-axis only
- Check the 1.8 V rail: the MPU-9250 needs VDD of at least 2.4 V and the LSM9DS1 at least 1.9 V
- Budget a driver rewrite for every candidate: none shares the ICM-20948 register map
Need the exact lot, date code or a second source quoted?
Send the original MPN and the approved alternative. Sourceics reconfirms source, stock, date code and commercial terms before any order — no substitution without your engineering approval.
Request a quote for ICM-20948Source part reference: TDK InvenSense product page. Equivalence notes are reference guidance, not a guarantee of fit — always verify against your schematic and layout.