TCAN1044ADRQ1 alternatives & equivalent parts
TI automotive fault-protected CAN FD transceiver with low-power standby mode and remote wake-up over the CAN bus, for classical CAN (up to 1 Mbps) and CAN FD (up to 8 Mbps); 5 V supply (4.5-5.5 V), bus fault protection +/-58 V, AEC-Q100 Grade 1. This ordering code is the non-VIO variant: pin 5 is a no-connect and pin 8 is STB. — common packages: SOIC-8 (D). Each candidate below cites its manufacturer datasheet; check the relationship badge before substituting.
3 verified alternatives for TCAN1044ADRQ1
| Alternative | Manufacturer | Relationship | Key differences | Source |
|---|---|---|---|---|
| TCAN844DRQ1 | Texas Instruments | Pin-compatibleDrop-in: same footprint and pinout. | Pinout is identical to the source, including pin 5 = NC on this non-V orderable (VIO, 2.9-5.25 V, exists only on the V version, TCAN844VDRQ1) and pin 8 = STB with the same standby plus remote wake-up behaviour; TI itself positions the TCAN844-Q1 as the cost-optimized pin-compatible alternate. The downgrades are parametric: maximum signaling rate drops from 8 Mbps to 5 Mbps, bus fault protection drops from +/-58 V to +/-40 V, and VCC narrows from 4.5-5.5 V to 4.75-5.25 V (TI's comparison table lists the 844 for 12 V battery systems versus 12 V/24 V for the 1044A). | TI datasheet |
| TJA1044GT | NXP | Pin-compatibleDrop-in: same footprint and pinout. | The SO8 pinout matches pin-for-pin: 1 TXD, 2 GND, 3 VCC, 4 RXD, 5 n.c. on the GT variant (VIO only on GT/3 and BT variants), 6 CANL, 7 CANH, 8 STB, with the same standby mode and ISO 11898-2 remote wake-up via RXD. Differences: CAN FD timing is guaranteed only up to 5 Mbit/s versus the source's 8 Mbps, and the plain TJA1044T variant is expressly excluded from that CAN FD guarantee, so only the GT/CT variants are pin-to-pin usable (BT is excluded: its pin 5 is VIO, not the source's NC); bus-pin limiting values are -42 V to +42 V versus TI's +/-58 V fault protection, and VCC is 4.5-5.5 V, the same as the source (no narrowing). | NXP datasheet |
| TJA1051T | NXP | Functional alternativeSame function: board or design change needed. | Pins 1-7 land in the same places (pin 5 = n.c. on the TJA1051T; VIO on TJA1051T/3, EN on TJA1051T/E), but pin 8 is S (Silent mode), not STB: the device has no standby mode and no remote wake-up, and NXP explicitly targets it at nodes that do not require standby mode with wake-up capability via the bus, so a board wired for STB standby/wake loses that function. Parametrically it is strong elsewhere: CAN FD fast-phase timing guaranteed up to 5 Mbit/s, bus pins withstand -58 V to +58 V limiting values (the same class as the source), VCC is 4.5-5.5 V, and Silent mode still draws 0.1-2.5 mA rather than a microamp-level standby current. | NXP datasheet |
Pre-replacement checklist
- Confirm pin 5: the source is the non-VIO variant (pin 5 = NC); if your design needs VIO, order the V variants instead of treating them as the same part
- Confirm pin 8 behaviour: STB standby with bus wake-up (TCAN844, TJA1044) versus Silent-only (TJA1051)
- Check the CAN FD rate you actually run: all three candidates are guaranteed to 5 Mbps, the source to 8 Mbps
- Check bus fault exposure: +/-40 V (TCAN844) and +/-42 V (TJA1044) are below the source's +/-58 V class
Need the exact lot, date code or a second source quoted?
Send the original MPN and the approved alternative. Sourceics reconfirms source, stock, date code and commercial terms before any order — no substitution without your engineering approval.
Request a quote for TCAN1044ADRQ1Source part reference: TI datasheet. Equivalence notes are reference guidance, not a guarantee of fit — always verify against your schematic and layout.