TSC2046 alternatives & equivalent parts
TI 4-wire resistive touch screen controller with a 12-bit, 125 kHz SAR ADC over SPI/QSPI, internal 2.5 V reference, direct battery measurement (0-6 V), on-chip temperature and touch-pressure measurement; supply 2.2-5.25 V with a separate 1.5-5.25 V digital I/O range. — common packages: TSSOP-16 / QFN-16. Each candidate below cites its manufacturer datasheet; check the relationship badge before substituting.
3 verified alternatives for TSC2046
| Alternative | Manufacturer | Relationship | Key differences | Source |
|---|---|---|---|---|
| ADS7846 | Texas Instruments | Pin-compatibleDrop-in: same footprint and pinout. | TI states verbatim that the TSC2046 is 100% pin-compatible with the existing ADS7846 and will drop into the same socket; both share the TSSOP-16/QFN-16/VFBGA-48 packages and the same feature set (internal 2.5 V reference, battery/temperature/touch-pressure measurement, 125 kHz conversion). The one real gap is the digital interface: the TSC2046 adds a low-voltage I/O range of 1.5-5.25 V independent of supply, while the ADS7846's I/O runs at supply level and its datasheet lists 2.2–5.25 V operation (2.7 V is a test-condition point, not the supply floor), so sub-2.7 V or 1.5/1.8 V-logic designs must be checked before treating it as a drop-in. | TI datasheet |
| ADS7843 | Texas Instruments | Functional alternativeSame function: board or design change needed. | The pin assignment matches (TI's ADS7846 datasheet headline is 'same pinout as ADS7843', and the ADS7846 is itself 100% pin-compatible with the ADS7843), but the ADS7843 is offered only in SSOP-16, with no TSSOP-16 or QFN-16 option, so it does not fit a TSC2046 TSSOP/QFN footprint. It is also functionally reduced: no internal reference (an external VREF of 1 V to +VCC is required), no battery measurement, no temperature measurement and no touch-pressure measurement, a 2.7–5 V supply (one Theory of Operation sentence says 5.25 V) and no 1.5 V I/O; what carries over is the 12-bit ADC at up to 125 kHz, two auxiliary inputs and PENIRQ. | TI datasheet |
| STMPE811 | STMicroelectronics | Functional alternativeSame function: board or design change needed. | ST's S-Touch controller integrates the same job (4-wire resistive touch with a 12-bit ADC) plus an 8-channel GPIO expander, a 128 x 32-bit touch FIFO and movement tracking, over SPI or I2C. It is a redesign, not a swap: QFN-16 3 x 3 mm only, a completely different pinout and register model, and a 1.65-3.6 V recommended supply range (VCC and VIO, with VIO ≥ VCC), so it cannot serve a 5 V TSC2046 design. It also lacks the TSC2046's battery-monitor input and a 2.5 V internal reference (its internal reference is selectable, but not 2.5 V), while adding GPIO and FIFO features the TI part does not have. | ST datasheet (PDF, distributor mirror) |
Pre-replacement checklist
- Check the logic level first: only the TSC2046 supports 1.5-5.25 V I/O independent of supply
- Confirm the footprint: the ADS7843 is SSOP-16 only and the STMPE811 is QFN-16 only
- List the features you use (internal reference, battery and temperature measurement): the ADS7843 drops all three
- Check the supply ceiling for redesigns: the STMPE811 recommended supply tops out at 3.6 V (VIO ≥ VCC), so it still cannot serve a 5 V design
Need the exact lot, date code or a second source quoted?
Send the original MPN and the approved alternative. Sourceics reconfirms source, stock, date code and commercial terms before any order — no substitution without your engineering approval.
Request a quote for TSC2046Source part reference: TI datasheet. Equivalence notes are reference guidance, not a guarantee of fit — always verify against your schematic and layout.